Struct Piix4Pm

pub struct Piix4Pm { /* private fields */ }

PIIX4 (PCI device function 3) - Power Management

See section 3.4 in the PIIX4 data sheet.

Implementations

impl Piix4Pm

pub fn new( power_action: PowerActionFn, interrupt: LineInterrupt, register_pio: &mut dyn RegisterPortIoIntercept, vmtime: VmTimeAccess, pm_timer_assist: Option<Box<dyn PmTimerAssist>>, ) -> Self

Trait Implementations

impl ChangeDeviceState for Piix4Pm

fn start(&mut self)

Starts a device, allowing it to interact with the guest asynchronously.

async fn stop(&mut self)

Stops a device’s asynchronous work.

async fn reset(&mut self)

Resets the device state to its initial state, for a fresh boot.

impl ChipsetDevice for Piix4Pm

fn supports_pio(&mut self) -> Option<&mut dyn PortIoIntercept>

Optionally returns a trait object to send IO port intercepts to.

fn supports_pci(&mut self) -> Option<&mut dyn PciConfigSpace>

Optionally returns a trait object to send PCI config space accesses to.

fn supports_line_interrupt_target( &mut self, ) -> Option<&mut dyn LineInterruptTarget>

Optionally returns a trait object to send interrupt line changes to.

fn supports_mmio(&mut self) -> Option<&mut (dyn MmioIntercept + 'static)>

Optionally returns a trait object to send MMIO port intercepts to.

fn supports_poll_device(&mut self) -> Option<&mut dyn PollDevice>

Optionally returns a trait object to send poll requests to.

fn supports_handle_eoi(&mut self) -> Option<&mut dyn HandleEoi>

Optionally returns a trait object to send EOI requests to.

fn supports_acknowledge_pic_interrupt( &mut self, ) -> Option<&mut dyn AcknowledgePicInterrupt>

Optionally returns a trait object with which to acknowledge PIC interrupts.

impl InspectMut for Piix4Pm

fn inspect_mut(&mut self, req: Request<'_>)

Inspects the object.

impl LineInterruptTarget for Piix4Pm

Target for lines corresponding to bits in General Purpose Event Block 0.

For a specific description of an implementation of this, see the PIIX4 manual, section 7.2. The PIIX4 manual calls this register the “General Purpose Status Register”

fn set_irq(&mut self, vector: u32, high: bool)

Set an interrupt line state.

fn valid_lines(&self) -> &[RangeInclusive<u32>]

Returns the valid vector ranges for this target.

impl PciConfigSpace for Piix4Pm

Sidestep the config space emulator, and match legacy stub behavior directly

fn pci_cfg_read(&mut self, offset: u16, value: &mut u32) -> IoResult

Dispatch a PCI config space read to the device with the given address.

fn pci_cfg_write(&mut self, offset: u16, value: u32) -> IoResult

Dispatch a PCI config space write to the device with the given address.

fn suggested_bdf(&mut self) -> Option<(u8, u8, u8)>

Check if the device has a suggested (bus, device, function) it expects to be located at.

impl PortIoIntercept for Piix4Pm

fn io_read(&mut self, io_port: u16, data: &mut [u8]) -> IoResult

Dispatch an IO port read to the device with the given address.

fn io_write(&mut self, io_port: u16, data: &[u8]) -> IoResult

Dispatch an IO port write to the device with the given address.

fn get_static_regions(&mut self) -> &[(&str, RangeInclusive<u16>)]

Report a set of static io port regions (region_name, port_range) that cannot be remapped at runtime and are always registered.

impl SaveRestore for Piix4Pm

type SavedState = SavedState

The concrete saved state type.

fn save(&mut self) -> Result<Self::SavedState, SaveError>

Saves the object’s state.

fn restore(&mut self, state: Self::SavedState) -> Result<(), RestoreError>

Restores the object’s state.